Late Stage Damage in G30-500/PMR-15 Laminates
Damage progression has been studied experimentally under tension using [02/906]s...
Thermal Stresses in Piezoelectric Materials: A Boundary Integral Formulation
With the increasing use of piezoelectric materials in electromechanical devices which are often required to function in thermally hostile environment, thermal stresses and their influence...
Convergence Rates of the Method of Successive Elastic Solutions in Thermoplastic Problems of a Layered Concentric Cylinder
This paper examines convergence rates of the method of successive elastic solutions, proposed by Mendelson, in determining the thermoplastic response of an arbitrarily layered concentric...
Implementation of a Viscoplastic, Kinematic Hardening Constitutive Model for Impact Prediction
This paper reports on a preliminary study to determine the significance of the Bauschinger effect on modeling impact and other large deformation events. Such events have significant implications...
Physical Model Tests of Dolos Impact Stresses
An on-going experimental study to determine impact stresses and static nesting stresses in instrumented large scale model dolosse is described in this paper. Seven dolosse were instrumented...
Comprehensive Reliability Analysis of Prestressed Concrete Beams
Using second moment methods, the reliability with respect to several limit states for seventy three prestressed concrete beams is assessed. These beams that are extensively used in the...
Behavior of RC Beams under Sustained Load
Experimental results of eight reinforced concrete beams under 3-month's sustained load, with the ratio of shear span to depth equal to 2.5, are reported. It is shown by tests that the...
Load Rate Effects on Concrete Compressive Strength
Plain concrete cylindrical specimens from six different concrete mixes, 51 mm in length and diameter, were tested in compression quasi-statically at strain rates between 10-6/sec...
The Canadian Approach in the Design of Wood Structures: Conversion to Limit States Design
During the early 70's, the National Building Code of Canada (NBCC) established the principle that structural design be carried out using the limit states design (LSD) method. The technical...
LRFD Provisions for Wood Bridges
A project to develop a load and resistance factor design (LRFD) edition of the American Association of State Highway and Transportation Officials (AASHTO) Standard Specifications for Highway...
Test Experience with Heavy Angle Dead End Lattice Transmission Towers
During the past three years, the Electric Power Research Institute's Transmission Line Mechanical Research Center has conducted full scale tests on three 500kV heavy angle dead end lattice...
Metal Truss Plates: Less than Full-Depth Penetration and Shear Buckling
This paper presents the results of two experimental studies on metal truss plates which are used to join members of wood trusses. The first study investigated the effect that less than...
Shear Design Guidelines for Polyester Concrete Using Recycled Plastic
Previous research on the shear behavior of steel-reinforced polymer concrete (PC) beams has been very limited and no efficient design procedures have been proposed. In all the previous...
Fatigue Damage Accumulation Under Stochastic Stress Histories
An extensive simulation study was performed to generate random Gaussian stress time histories from power spectral densities (psd's). The psd's of time histories were selected to represent...
High-Strain Kinetic Testing of Deep Foundations
High-strain kinetic testing involves the upward decelerating or accelerating of a mass and using its inertial force to axial prolonged pulse at the head of a pile. Currently available...
Low Strain Dynamic Testing of Wood Piles Supporting an Existing Pier
This paper presents a case history where low strain dynamic testing was performed to test wood piles supporting an existing structure. Under consideration is a 183 m long wooden pier constructed...
A Nonlinear-Analysis-Based Procedure for Evaluating Load-Carrying Capacity of In-Plane Steel Frames
A simple method based on geometrically nonlinear analysis is proposed to evaluate the load-carrying capacity of a steel structure. The effects of material nonlinearity and residual stress...
Anchorage of Non-Metallic Prestressing Tendons
Experimental confirmation tests were conducted to evaluate mechanical and epoxy socketed anchors for fiber reinforced plastic (FRP) prestressing tendons. The studies found that a parabolically...
Steady-State Analysis of Buckle Propagation
A novel finite element technique for the analysis of buckle propagation in pipelines is presented. The propagation pressure, propagation profile, the state of stress, and deformation during...
A Generalized Approach to the Local Stability of Stiffened Plates: Part I?Mathematical Formulation
The paper describes a generalized approach for the determination of the buckling stress of stiffened plates under combination of uniform biaxial compression, in-plane bending and shear...
Return to search